Lincoln Nautilus: Information and Entertainment System - General Information - Vehicles With: SYNC 4 / Audio Unit Antenna Cable. Removal and Installation
Removal
NOTE:
The original equipment body and liftgate audio unit antenna
cable(s) are part of the wiring harness and cannot be removed. This
procedure refers to replacement of the cable(s) only by overlaying the
cable(s).
NOTE:
The instrument panel-to-body audio unit antenna cable inline connection is located under the floor console.
NOTE:
The audio unit antenna cable and the satellite radio antenna
cable are routed together. This procedure refers to the replacement of
both cables as the cables cannot be separated.
Instrument panel audio unit antenna cable
-
Remove the information and entertainment display unit.
-
Remove the ACM .
Refer to: Audio Front Control Module (ACM) (415-00 Information and
Entertainment System - General Information - Vehicles With: SYNC 4,
Removal and Installation).
-
Remove the GSM
Refer to: Gear Shift Module (GSM) (307-05A Automatic Transmission
External Controls - 8-Speed Automatic Transmission – 8F57, Removal and
Installation).
-
Release the clips, position the center instrument
trim panel, disconnect the electrical connector and remove the center
instrument trim panel.
-
Disconnect the satellite radio / GPS splitter / cable cable electrical connector.
-
Disconnect the satellite radio / GPS splitter / cable lower connector.
-
Separate the wiring guides and remove the satellite radio / GPS splitter / cable.
Body audio unit antenna cable
-
Remove the following items:
-
Refer to: Front Seat (501-10A Front Seats, Removal and Installation).
-
Refer to: Floor Console (501-12 Instrument Panel and Console, Removal and Installation).
-
Refer to: B-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
Refer to: C-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
Refer to: D-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
Refer to: Loadspace Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
-
Refer to: Headliner - Lowering (501-05 Interior Trim and Ornamentation, Removal and Installation).
Liftgate audio unit antenna cable
-
Remove the liftgate trim panel.
Refer to: Liftgate Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
Installation
Instrument panel audio unit antenna cable
-
To install, reverse the removal procedure.
Body audio unit antenna cable
-
NOTE:
D-pillar audio unit anteanna cable routing shown.
Cut the ends off the old antenna cable. Overlay the
new antenna cable on the vehicle wiring harness following the routing
shown. Secure the new antenna cable to the wiring harness with tape or
zip ties as necessary.
-
NOTE:
Floor audio unit antenna cable routing shown.
Cut the ends off the old antenna cable. Overlay the
new antenna cable on the vehicle wiring harness following the routing
shown. Secure the new antenna cable to the wiring harness with tape or
zip ties as necessary.
Liftgate audio unit antenna cable
-
NOTE:
Liftgate audio unit antenna cable routing shown.
Cut the ends off the old antenna cable. Overlay the
new antenna cable on the vehicle wiring harness following the routing
shown. Secure the new antenna cable to the wiring harness with tape or
zip ties as necessary.
Removal
NOTE:
Removal steps in this procedure may contain installation details.
All vehicles
Remove the liftgate trim panel.
Refer to: Liftgate Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation)...
Removal
Instrument panel cable
NOTE:
The original equipment automotive audio bus (AAB) cable
is part of the instrument panel wiring harness and cannot be removed...
Other information:
Special Tool(s) /
General Equipment
Interior Trim Remover
Removal
Remove the screw and using the non-marring tool, position the side parking aid camera.
Use the General Equipment: Interior Trim Remover
Disconnect the side parking aid camera electrical connector...
Removal
NOTICE:
During the removal of components, cap, tape or otherwise
appropriately protect all openings to prevent the ingress of dirt or
other contamination. Remove protective materials prior to installation.
NOTE:
Removal steps in this procedure may contain installation details...
Categories
What Is Auto-Start-Stop
The system is designed to help reduce fuel
consumption and CO2 emissions by stopping
the engine when it is idling, for example at
traffic lights.
Auto-Start-Stop Precautions
WARNING: Apply the parking brake,
shift into park (P), switch the ignition off
and remove the key before you leave your
vehicle. Failure to follow this instruction
could result in personal injury or death.
WARNING: Apply the parking brake,
shift into park (P), switch the ignition off
and remove the key before you open the
hood or have any service or repair work
completed. If you do not switch the ignition
off, the engine could restart at any time.
Failure to follow this instruction could result
in personal injury or d
read more