Lincoln Nautilus Manuals

Lincoln Nautilus: Exterior Trim and Ornamentation / Finish Panel Repair. General Procedures

Repair

NOTE: Mouldings located on the front and rear window frames may experience minor scratches from vehicle shipment or car wash racks. The imperfections may be repaired instead of replacing components by following the steps below.

NOTE: Scratches deep enough to cause a thumb nail to catch cannot be repaired and the component must be replaced.

  1. Clean with a mild soap and water wash, and dry the affected panels.
  1. Apply protective masking to adjacent components.
  1. Apply a small amount of clear coat and plastic formulated polishing compound (obtain locally) to a 3 inch polisher with an appropriate foam pad attached.
  1. NOTE: Do not allow the polishing compound to dry while polishing the component.

    Thoroughly polish the component.
  1. Reclean with a mild soap and water wash and dry the polished panels.
    • If the scratches are repaired return the vehicle.
    • If the scratches remain, continue with the following steps.
  1. Choose a sandpaper grit appropriate to the scratch severity.
    • For very minor scratches, use a 3 inch 3000 grit sandpaper (obtain locally).
    • For minor scratches, use a 3 inch 1000 grit sandpaper (obtain locally).
    • For heavier scratches that do not catch a thumb nail when pulled across the scratch, use a 3 inch 800 grit sandpaper (obtain locally).
    • For scratches that are too deep to remove with 800 grit sandpaper, install a new component.
  1. NOTICE: Do not remove any more material than necessary or component replacement will be required.

    Apply the appropriate sandpaper to a 3 inch Dual Action (D/A) sander and carefully sand the component until all the damage has been removed.
  1. Use progressively finer sandpaper with the 3 inch D/A sander and repeat the process. Finish the sanding with 3000 grit sandpaper.
  1. Apply a small amount of clear coat and plastic formulated rubbing compound (obtain locally) to a 3 inch polisher with an appropriate foam pad attached.
  1. NOTE: Do not allow the rubbing compound to dry while polishing the component.

    Buff the component until the sanding scratches have been completely removed.
  1. Apply a small amount of clear coat and plastic formulated polishing compound (obtain locally) to a 3 inch polisher with an appropriate clean foam pad attached.
  1. NOTE: Do not allow the rubbing compound to dry while polishing the component.

    Polish the component until the buffing swirl marks are removed.
  1. Continue polishing the component until the original level of shine is present.
  1. Apply a small amount of clear coat and plastic formulated hand glaze (obtain locally) to a soft and clean shop cloth and hand polish to remove swirl marks left by the 3 inch polisher.

    Exterior Trim and Ornamentation

    ..

    D-Pillar Moulding. Removal and Installation

    Removal NOTE: LH side shown, RH side similar. NOTE: Removal steps in this procedure may include installation details. Remove the pushpins...

    Other information:

    Lincoln Nautilus 2018-2025 Owners Manual: Memory Function


    How Does the Memory Function Work The memory function recalls the position of these features: Driver seat. Power mirrors. Optional power steering column. Memory Function Precautions WARNING: Before activating the memory seat, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts...

    Lincoln Nautilus 2018-2025 Service Manual: Rear Gate Trunk Module (RGTM). Removal and Installation


    Removal NOTE: This step is only necessary when installing a new component. NOTE: The PMI process must begin with the current RGTM installed. If the current RGTM does not respond to the diagnostic scan tool, the tool may prompt for As-Built Data as part of the repair...

    Categories

    Changing a Flat Tire

    WARNING: If the tire pressure monitor sensor becomes damaged it may not function.

    Note: The use of tire sealant may damage your tire pressure monitoring system and should only be used in roadside emergencies. If you must use a sealant, use the Tire Mobility Kit sealant. Replace the tire pressure monitoring system sensor and valve stem on the wheel by an authorized dealer after use of the sealant.

    Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle.

    If you get a flat tire while driving, do not apply the brake hea

    read more

    Copyright © 2025 www.linautilus.com